Schedule Free Estimate

 

Each person is bound to have his or her own way of thinking in relation to Installing A Bathtub.

Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a new one is also a moderately hard task. If the old tub is readily easily accessible, the task can move quickly; if you need to open up a wall surface to remove the old tub and also place the brand-new bath tub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will require a helper to move out the old bathtub as well as set in the new one. Make sure you have certified yourself for the task as well as are comfortable trying it. Rather than hiring a service provider to take control of a halfway-completed project, it is much better to think about employing one before you start. Possibilities are you might need a professional plumber to make tube links.
This write-up will assist you set up a new bathtub in your shower room if you have actually already purchased a brand-new tub as well as don't need to change the setup of your previous water supply pipes.
Your devices as well as product list must consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water system. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be rather problematic because of the limited access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Prior to going on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the various other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet as well as the sink. Protect the tap in position with the maker offered backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The former kind needs to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Installing the Bathtub

Using the two wood boards under its feet, position the tub in the needed setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and changing the feet on the tub till the spirit level reads degree.
To mount taps, fit the bottom of the furthest adaptable faucet adapter to the suitable supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the water and inspect all joints and brand-new pipework for leakages as well as tighten them if required. Load the bathtub and also examine the overflow electrical outlet and the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub ought to wait till the tub has actually been utilized a minimum of once as this will certainly settle it into its final setting.

 

 

Planning for the Setup

Firstly, the supporting frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.

 

 

Tiling Around the Bathtub

In the location where the bathroom fulfills the tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, leading to complications with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the tub remains in use. The sealant can break rather early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently offered on the market. It is suggested to fit the floor tiles using waterproof or water resistant glue as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I came across that post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while surfing the search engines. Loved our posting? Please share it. Help someone else check it out. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.

Instant help? Contact.